1/4/2024 0 Comments Raspberry pi openvpnThis means changing that line to "auth-user-pass vpnlogin". Remember that line in the VPN configuration file for "auth-user-pass"? We need to change that so that credentials file we just created is called automatically. conf file you want to connect to (excluding the file type). Want the VPN to start whenever the Pi boots up? Use this command: sudo systemctl enable where "example" is the name of the. Now you can make your PlayStation or Roku Box magically appear in another country without leaving your lounge. Leave everything in its default setting apart from the Gateway and DNS servers.Ĭhange Gateway to the IP address of your Pi, and set the DNS server to 1.1.1.1, 8.1.1.8.Īnd that’s it. Route Device Traffic Through the Piįinally, in order to route traffic via the Pi, you’ll need to go back to your game console, set-top box (or other device) and change the internet settings. Now, you can start or switch your connection by SSHing into the Pi from any computer on the network and typing sudo. Repeat this step for the three or four VPN connections you think you’ll use the most, adding one to the number in the filename. #!/bin/bashsudo killall openvpnsudo -b openvpn /etc/openvpn/example.ovpnģ. Enter the following code in the file, save and exit it: Back in your home folder (usually /home/pi), type nano vpn1.sh.Ģ. It begins with an instruction to close any open VPN connections, then starts the OpenVPN daemon filling in the credentials from the text file we just created.ġ. Remember that you took a note of your most likely used servers right back at the start? We’re going to create a quick script that will let you start and switch between those with a simple command. So far so good, but we don’t want to have to type a long command every time we need to connect to a VPN. (See boxout to change all the config files at once.) Quick start Commands for Different VPN Servers Now when you start that connection using the "openvpn" command, it should connect directly without the password prompt. Change the line that says "auth-user-pass" to "auth-user-pass vpnlogin". P ick the VPN connection you think you’ll use the most and edit the config file using sudo nano example.ovpn.ĥ. Hit CTRL+O to write the contents to disk, then CTRL+X to quit nano.Ĥ. Create a text document that has nothing except your username for the VPN provider on the first line, and your password on the second.ģ. This should open up the nano text editor.Ģ. N avigate to /etc/openvpn and type sudo nano vpnlogin. We can alter this line to automatically feed a username and password to our config file when it is called.ġ. These include a line that contains "auth-user-pass". You should see that it starts with client and that there’s a list of commands. Take a look at the VPN files you downloaded to your desktop and open one of them. Good, but it could be better – we’re going to create a few scripts to automatically create your credentials. So far we have a slightly cumbersome way of connecting our Pi to a VPN via a terminal which requires you to enter your username and password when you want to connect. You should see a connection marked "TUN", which is your VPN tunnel. Do test to see if the connection is working by typing ifconfig. If you try this now, you’ll notice that the script asks for your username and password to authenticate the connection. O pen a connection to any of these servers using the command sudo openvpn example.ovpn –daemon where "example" is the filename of the configuration file. You’ll need to move the files to the etc/openvpn directory using the mv command.ĥ. Note that some VPN providers may have packaged these files with subdirectories, for example for connections encrypted with optional 128bit or 256bit protection. There should be a list of files ending in. If you’re using a headless Pi, connect via SSH.Ī quick "ls" command will show if you have been successful. Log into your Pi and navigate to the command prompt. Download them and unzip them into a folder on your desktop.ġ. You should find these configuration files on your VPN provider’s website (ours are at /servers). We opted for two UK and two US servers, choosing one that supports the UDP protocol and one that supports TCP/IP. There are usually a lot of these – one for each server you have the option to connect to – so pick a handful that you want to be able to quickly access.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |